On this page
Key takeaways
- Test hot and cold separately. Eggy smell from hot only points to your cylinder or water heater; both hot and cold points to the supply or drains.
- The smell is usually hydrogen sulphide made by bacteria in warm stored water, especially after the system has been idle or run at low temperatures.
- Defra guidance, quoted by WaterSafe, says hot water should be stored at no less than 60°C to control Legionella. Keeping to that also discourages smell-causing bacteria.
- Cylinders and water heaters with a magnesium anode can make the problem worse. Replacing or changing the anode is an engineer job.
- A gas leak smells in the air near appliances and pipes, not in the water. That is an emergency.
When your hot water smells of eggs but the cold water is fine, the cause is almost always inside your own hot water system, not the mains supply. The usual culprit is bacteria growing in warm, stored water in a hot water cylinder or water heater, producing hydrogen sulphide gas, sometimes helped along by the cylinder’s metal anode. Raising and holding the stored temperature, flushing the cylinder and having the anode checked usually cures it. If both hot and cold smell, or you think the smell is gas rather than water, the steps are different.
If you are not sure whether you can smell gas or water, treat it as gas. Turn off the gas at the meter if you can, do not use electrical switches or flames, open windows, leave the property and call the National Gas Emergency Service on 0800 111 999. Our guide on what to do if you smell gas explains each step.
Is it the water or a gas leak?
Both are described as rotten eggs, which is why people worry. The difference is where the smell comes from:
| Smell from the water | Smell of gas |
|---|---|
| Strongest when you run a tap or fill a bath | In the air, often near the boiler, cooker, meter or gas pipes |
| Fades when the tap is turned off | Persists or builds with no tap running |
| Often only from the hot tap | Nothing to do with water use |
| Not dangerous in itself, but needs fixing | Emergency: call 0800 111 999 |
Mains gas has no smell of its own. Suppliers add an odorant so leaks can be detected, and it is that which smells sulphurous. If there is any doubt, follow the gas emergency steps first and work out the water later.
Hot tap only or every tap? Find the source
- Run the cold kitchen tap into a clean glass and sniff it away from the sink. The kitchen cold is normally fed straight from the mains.
- Run a hot tap into another glass and compare.
- Check a different hot tap elsewhere in the house.
- Smell the plughole with no water running. A drain smell can be mistaken for a water smell.
| What you find | Most likely source | Who deals with it |
|---|---|---|
| Hot smells, cold does not | Hot water cylinder or water heater | Heating engineer or plumber |
| Hot and cold both smell | Supply, a private supply, or internal pipework | Water company first |
| Only one tap smells | That tap’s pipe or a dead leg | Plumber |
| Smell from the plughole, not the water | Drain trap dried out or blocked | Run water to refill the trap; plumber if it persists |
| Smell only on a combi system | Less likely to be stored water; check pipework and supply | Plumber or water company |
If both hot and cold smell, contact your water company. The Drinking Water Inspectorate advises that your water company should be your first contact, and it can advise and test the water if needed. If you are unhappy with the response, you can take it up with the Inspectorate.
Why stored hot water starts to smell
Water naturally contains small amounts of sulphate and harmless bacteria. In a cylinder held at lukewarm temperatures, some bacteria thrive and convert sulphate into hydrogen sulphide, the gas that smells of rotten eggs. The conditions that encourage it are:
- Low stored temperature. Cylinders set well below 60°C to save energy give bacteria a comfortable home.
- Stagnant water. Homes left empty, holiday lets, or a cylinder that is barely used.
- Solar or heat pump systems where water spends long periods at moderate temperature, if pasteurisation is not set up.
- Sediment at the bottom of the cylinder, giving bacteria somewhere to settle.
The role of the anode
Some cylinders and water heaters, particularly those with enamelled steel tanks, have a sacrificial anode, usually a rod of magnesium, that corrodes instead of the tank. The reaction between the anode and the water can feed the smell-producing process. Copper and many stainless steel cylinders do not have one, so this cause depends on your cylinder. The manufacturer’s manual or data label will tell you, or an engineer can check during a service.
How to get rid of an eggy smell from hot water
1. Check the cylinder temperature
Look at the thermostat on your cylinder, or the hot water setting on your boiler or controller. WaterSafe, quoting Defra guidance, says hot water should be stored at not less than 60°C to prevent Legionella, and distributed at no less than 55°C. If yours is set lower, a heating engineer can reset it and confirm the cylinder actually reaches that temperature.
2. Pasteurise the cylinder
Heating the whole cylinder to a high temperature for a period kills bacteria throughout the tank. Many cylinders with an immersion heater, solar coil or heat pump controller have a pasteurisation or anti-legionella function. Our cylinder pasteurisation and Legionella guide explains how it works and how often it should run. Take care with scalding while water is very hot, especially with children or older people in the home.
3. Flush the system
After pasteurising, run every hot tap in turn until the water is hot, to clear smelly water from the pipes. Draining and flushing the cylinder to remove sediment is a job for a plumber or heating engineer, especially on unvented cylinders.
4. Have the anode inspected
If the smell keeps coming back and your cylinder has an anode, an engineer can inspect it and replace it with the type the manufacturer approves. Do not remove an anode yourself. On many cylinders that would void the warranty and allow the tank to corrode. Unvented cylinders also have safety devices that only a qualified installer should touch; our unvented cylinder service guide covers what an annual check includes.
5. Consider the cylinder’s age
An old cylinder full of sediment, with a failing coil or thermostat, may be better replaced than repeatedly treated. Our guide to hot water cylinder replacement explains the options.
Is it safe to use smelly hot water?
Hydrogen sulphide at the low levels that cause a smell in tap water is unpleasant rather than dangerous. The bigger concern is what the smell tells you: water stored warm enough for bacteria to grow. The same conditions can encourage Legionella, which causes Legionnaires’ disease and is spread by breathing in fine water droplets, for example from a shower. Fix the temperature problem promptly, and avoid showering in smelly hot water if anyone in the household is elderly, unwell or has a weakened immune system.
Never drink or cook with water from the hot tap. Use the cold kitchen tap for drinking and food.
Landlords and empty properties
Rented homes, holiday lets and properties left empty over winter are especially prone to stagnant hot water. Landlords have a duty to assess and control the risk of Legionella in their properties, and a hot water system that smells is a sign that control may have slipped. Our guide to heating an empty rental property in winter covers keeping systems in safe condition between tenants.
Get the smell sorted
Work out whether the smell is in the hot water only, then check how hot your cylinder is storing water. Most eggy hot water problems come down to temperature, sediment or the anode, and all are fixable. If you have any doubt about whether it is gas, call the emergency number first.
Gasmaster’s engineers service cylinders, set up safe stored water temperatures and replace worn parts across Stoke-on-Trent, Staffordshire, Cheshire and Derbyshire. See our plumbing services or contact us to book an engineer.
[googlesitekit-end-of-content]
Frequently asked questions
Why does my hot water smell of eggs but not my cold?
Because the cause is in the stored hot water rather than the supply. Bacteria in a cylinder or water heater kept lukewarm can produce hydrogen sulphide, which you smell when the hot tap runs. Check the cylinder is storing water at 60°C, pasteurise it, and have an engineer look at the anode if the smell returns.
Can a combi boiler make hot water smell of eggs?
It is much less common, because a combi heats water on demand and does not store it. If hot water from a combi smells, check whether the cold smells too and whether one tap is worse than others. Possible causes include pipework, a little-used branch of pipe or the incoming supply. Ask a plumber or your water company to investigate.
Will turning up the cylinder thermostat stop the smell?
Often it helps, because bacteria that cause the smell do not do well at higher temperatures. Storing at 60°C is also the Defra guidance for Legionella control. If the smell has been there a while, pasteurising and flushing may also be needed, and an anode may need replacing, so the thermostat alone may not fix it.
Who do I call about smelly tap water?
If both hot and cold taps smell, call your water company first; its number is on your bill. If only the hot water smells, call a plumber or heating engineer to check your cylinder. If you think you can smell gas rather than water, call the National Gas Emergency Service on 0800 111 999 straight away.
Related services




